{"id":13157,"date":"2022-06-22T16:19:00","date_gmt":"2022-06-22T08:19:00","guid":{"rendered":"https:\/\/rewa.tech\/macbook-a1989-cannot-boot-issue-repair\/"},"modified":"2024-05-10T14:46:12","modified_gmt":"2024-05-10T06:46:12","slug":"macbook-a1989-kann-nicht-starten-problem-reparatur","status":"publish","type":"post","link":"https:\/\/rewa.tech\/de\/macbook-a1989-cannot-boot-issue-repair\/","title":{"rendered":"MacBook A1989 kann nicht starten Problem Reparatur"},"content":{"rendered":"<p>Das MacBook A1989 kann nicht starten, das Problem wird durch einen Wasserschaden auf dem Bildschirm verursacht.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/A1989.png\" alt=\"\" width=\"154\" height=\"144\" title=\"\"><\/p>\n<p><strong>Modell:<\/strong>&nbsp;MacBook Pro 13\u2033 (A1989)<\/p>\n<p><strong>Jahr:<\/strong> 2018-2019<\/p>\n<p><strong>Kartennummer\uff1a<\/strong>820-00850-07<\/p>\n<\/p>\n<h2>Defekt-Ph\u00e4nomen<\/h2>\n<p>Wasserschaden verursacht die CPU nicht zu arbeiten und kann nicht booten. Resolder die CPU dann montieren das Telefon zu testen, aber wie das Wasser oder vielleicht Feuchtigkeit auf dem Bildschirm noch nicht vollst\u00e4ndig gel\u00f6scht, Ursache kurz, die CPU wurde wieder besch\u00e4digt!<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/Replace_the_CPU_chip.png\" alt=\"\" title=\"\"><\/p>\n<\/p>\n<h2>Fehlersuche<\/h2>\n<p>Zun\u00e4chst wissen wir, dass das Problem durch den Bildschirm und die CPU verursacht wird.<\/p>\n<ul style=\"list-style-type: circle;\">\n<li>Bei der Montage des Bildschirms muss dieser durch einen neuen ersetzt werden, um einen Kurzschluss zu vermeiden.<\/li>\n<li>F\u00fcr die CPU m\u00fcssen wir sie durch die Rework-Station ersetzen<\/li>\n<\/ul>\n<p>Messen Sie das Signal vom Bildschirmanschluss zur CPU<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/01__Measure_the_signal_from_the_screen_connector_to_the_CPU.png\" alt=\"\" title=\"\"><\/p>\n<p>Nach der Messung stellen wir fest, dass ein Pin mit der Masse kurzgeschlossen ist.<\/p>\n<p>(Diodenwert ist nur etwa 20)<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/02__One_pin_is_shorted_to_the_ground.png\" alt=\"\" title=\"\"><\/p>\n<p>Verfolgen Sie dieses Signal (<span style=\"font-family: Courier; font-size: 12.701pt;\">EDP_INT_AUX_P<\/span>) auf der Bitmap und dem Schaltplan ist er direkt mit der CPU verbunden, wie wir aus der Bitmap sehen k\u00f6nnen<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/04__The_signal_on_the_connector.png\" alt=\"\" title=\"\"><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/05__The_signal_on_the_CPU.png\" alt=\"\" title=\"\"><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/6__EDP_INT_AUX_is_shorted.png\" alt=\"\" title=\"\"><\/p>\n<h2><\/h2>\n<h2><span style=\"font-size: 14px; font-weight: 400;\">Wir m\u00fcssen also die CPU durch eine neue ersetzen.<\/span><\/h2>\n<p><span style=\"font-size: 14px; font-weight: 400;\"><\/span><\/p>\n<h2>Reparatur-Prozess<\/h2>\n<p><span style=\"font-size: 14px; font-weight: 400;\">Entfernen Sie zun\u00e4chst die CPU von der BGA-Rework-Station.<\/span><\/p>\n<p><span style=\"font-size: 14px; font-weight: 400;\"><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/07__remove_the_CPU.png\" alt=\"\" title=\"\"><\/span><span style=\"font-size: 14px; font-weight: 400;\"><\/span><\/p>\n<p><span style=\"font-size: 14px; font-weight: 400;\"><img fetchpriority=\"high\" decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/08__remove_the_CPU.png\" width=\"713\" height=\"593\" alt=\"\" title=\"\"><\/span><\/p>\n<p>Reinigen Sie dann die Pads auf der Leiterplatte<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/09__Then_clean_the_pads_on_the_PCB.png\" alt=\"\" title=\"\"><\/p>\n<\/p>\n<p>Messen Sie den Diodenwert an Pin 3 des Bildschirms (<span style=\"font-family: Courier; font-size: 12.701pt;\">EDP_INT_AUX_P)<\/span>wieder, der Diodenwert ist wieder normal<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/10__Measure_the_diode_value_on_the_again__the_diode_value_back_to_normal.png\" alt=\"\" title=\"\"><\/p>\n<p>Als letzten Schritt m\u00fcssen wir nur noch die CPU wieder an die Hauptplatine l\u00f6ten<\/p>\n<ul>\n<li>Tragen Sie etwas Kolophonium auf die PCB-Pads und die neue CPU auf.<\/li>\n<\/ul>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/11__Apply_solder_paste_flux_on_the_CPU_and_PCB_board.png\" alt=\"\" width=\"724\" height=\"1163\" title=\"\"><\/p>\n<ul>\n<li>\u00dcberpr\u00fcfen Sie, ob die Pads auf der CPU in Ordnung sind.<\/li>\n<\/ul>\n<p><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/12__check_the_pads_on_the_CPU.png\" alt=\"\" width=\"725\" height=\"769\" title=\"\"><\/p>\n<ul>\n<li>Stellen Sie sicher, dass die CPU gut auf die Pads auf der Leiterplatte ausgerichtet ist.<\/li>\n<\/ul>\n<p><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/13__ensure_the_CPU_is_well_aligned_with_the_pads_on_the_PCB.png\" alt=\"\" width=\"725\" height=\"562\" title=\"\"><\/p>\n<ul>\n<li>Legen Sie dann die Hauptplatine zum Erhitzen auf die BGA-Rework-Station<\/li>\n<\/ul>\n<p><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/14__Keep_heating_to_around_200.png\" alt=\"\" width=\"726\" height=\"704\" title=\"\"><\/p>\n<ul>\n<li>Wenn die Heiztemperatur der BAG Rework Station die <span style=\"color: #0000ff;\">200\u2103<\/span>wird die CPU zu schmelzen beginnen und auf die Platine gel\u00f6tet werden.<\/li>\n<\/ul>\n<pre><em>(w\u00e4hrend des Prozesses k\u00f6nnen wir durch den Spalt den Schmelzvorgang beobachten)<\/em><\/pre>\n<p><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/16__When_reaching_the_200____start_to_melt_and_solderded.png\" alt=\"\" width=\"725\" height=\"632\" title=\"\"><\/p>\n<\/p>\n<ul>\n<li>Nach dem Einl\u00f6ten der neuen CPU und dem Messen des Diodenwerts am Display-Anschluss ist der Diodenwert immer noch normal.&nbsp;<\/li>\n<\/ul>\n<p><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/MacBook_A1989_Cannot_Boot.png\" alt=\"MacBook A1989 l\u00e4sst sich nicht starten\" width=\"730\" height=\"582\" title=\"\"><\/p>\n<\/p>\n<ul>\n<li>Jetzt k\u00f6nnen wir etwas W\u00e4rmeleitpaste auf die CPU auftragen und dann den K\u00fchlk\u00f6rper montieren,<\/li>\n<\/ul>\n<p><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/18__Apply_some_thermal_grease_on_the_CPU_then_assemble_the_thermal_sink.png\" alt=\"\" width=\"724\" height=\"815\" title=\"\"><\/p>\n<\/p>\n<p>Zu guter Letzt bauen Sie das MacBook zusammen und starten es, um einen Test durchzuf\u00fchren. Das Ger\u00e4t kann normal gebootet werden und alle Funktionen sind auch OK getestet.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/rewa.tech\/wp-content\/uploads\/2024\/04\/17__The_Macbook_can_be_booted_normally.png\" alt=\"\" title=\"\"><\/p>\n<\/p>\n<h2>Gelernte Lektion<\/h2>\n<p>Achten Sie auf die Details der Reparatur, denn manchmal sind es nur Kleinigkeiten, die ernsthafte Probleme verursachen.<\/p>\n<p>In diesem Fall k\u00f6nnte das Problem vermieden werden, wenn Sie den Bildschirm zweimal \u00fcberpr\u00fcfen, sicherstellen, dass alles in Ordnung ist, und dann das MacBook wieder zusammenbauen.<\/p>\n<\/p>\n<p>&gt;&gt;&gt; Besuch <a href=\"https:\/\/academy.rewa.tech\/\">REWA-Akademie<\/a> um mehr \u00fcber n\u00fctzliche Reparaturkurse zu erfahren.<\/p>","protected":false},"excerpt":{"rendered":"<p>MacBook A1989 cannot boot, the issue is caused by water damage on the screen. Model:&nbsp;MacBook Pro 13&#8243; (A1989) Year: 2018-2019 Board Number\uff1a820-00850-07 Defect Phenomenon Water damage causes the CPU not to work and cannot boot. Resolder the CPU then assemble the phone to test, but as the water or maybe moisture on the screen still [&hellip;]<\/p>\n","protected":false},"author":10,"featured_media":13158,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"fifu_image_url":"","fifu_image_alt":"","footnotes":""},"categories":[782],"tags":[],"class_list":["post-13157","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-macbook-repair-case"],"_links":{"self":[{"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/posts\/13157","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/users\/10"}],"replies":[{"embeddable":true,"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/comments?post=13157"}],"version-history":[{"count":0,"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/posts\/13157\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/media\/13158"}],"wp:attachment":[{"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/media?parent=13157"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/categories?post=13157"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/rewa.tech\/de\/wp-json\/wp\/v2\/tags?post=13157"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}