{"id":2216,"date":"2021-03-09T11:23:18","date_gmt":"2021-03-09T11:23:18","guid":{"rendered":"http:\/\/192.168.2.19:8666\/?p=1"},"modified":"2023-10-19T18:42:19","modified_gmt":"2023-10-19T10:42:19","slug":"apple-watch-series-3-glass-replacement","status":"publish","type":"post","link":"https:\/\/rewa.tech\/de\/apple-watch-series-3-glass-replacement\/","title":{"rendered":"Apple Watch Series 3 Glass Replacement"},"content":{"rendered":"

As a wearable device launched by Apple, the Apple Watch product line market shipments and share are growing day by day. The demand for screen replacement and battery replacement has accordingly increased. Since the price of the display assembly and other parts is very high, REWA LAB will show you how to replace the glass of the Apple Watch Series 3. The solution will be more economical than the replacement of the display assembly.<\/p>\n

The tools and supplies needed are digitizer, OCA adhesive, adhesive strip, cutting wire, tweezers, pry bar, and razor blade.<\/p>\n

\"The<\/p>\n

Bildschirmtest<\/strong><\/h2>\n

First of all, test the screen. The touch, display, and Force Touch function well. Turn the watch off and pry the screen open with a Rasierklinge<\/a> slowly.
\n\"FirstLift the screen. Please pay attention to the screen flex cables to avoid damage. It can be seen that three flex cables are connected to the motherboard.
\n\"LiftPeel off the tape covering the display flex cables with tweezers. Please do not damage the flex cables while peeling off. Then disconnect the flex cables.
\n\"Peel<\/p>\n

Next, we need to pry up the connector of the touch flex cable. Put the screen on the Heizungsplattform<\/a> at 120\u2103 for 30 seconds. After heating, peel off the tape with tweezers and pry up the connector.<\/p>\n

\"Next,
\n\"Next,<\/p>\n

Glass Cutting<\/strong><\/h2>\n

Then we use the Cutting Machine<\/a> to cut the glass. We need to cut both sides of the glass to get the cutting wire in. Please be careful during the operation.
\n\"ThenWe can see that a side of the glass has been cut off and the bottom has broken too.
\n\"WeThen we cut the other side. Lastly, polish the corners. A point well mentioning is that the difficulty of replacement will be reduced if the glass is broken.
\n\"Then<\/p>\n

Glas Trennen<\/strong><\/h2>\n

Tape the screen. Then put the screen on the Heating Platform and start the suction.
\n\"TapeNext, separate the glass with Cutting Wire<\/a>. Pull the Cutting Wire slowly and the glass is successfully separated.
\n\"Next,<\/p>\n

OCA Removing<\/strong><\/h2>\n

Then we remove the OCA adhesive with the Electric Adhesive Removing Tool<\/a> and clean the OLED with N-hexane.
\n\"ThenInstall the OLED to test. Since the touch panel has been separated, we only need to test the display function. The display function is normal. Clean the OLED completely with N-hexane.<\/p>\n

\"Install<\/p>\n

Kaschieren<\/strong><\/h2>\n

Attach the OCA adhesive to the OLED with Laminating Roller<\/a>\u00a0<\/span>and put the OLED into the Maschine zum Entfernen von Luftblasen<\/a> for 3 minutes.
\n\"AttachTake the OLED out and put it into the UV Lamp for Curing OCA Glue<\/a> for 5 seconds.
\n\"TakeStick a corner of the OLED with Easy Tear Sticker and peel off the OCA protective film.
\n\"StickAttach the OLED to the Laminating Mold. Stick a corner of the Apple Watch Series 3 digitizer<\/a>\u00a0and peel off the OCA protective film.
\n\"AttachAlign the digitizer with the OLED.<\/p>\n

\"AlignDetach the screen and put the screen on the Laminating Sponge. Then put the screen into the Kaschiermaschine<\/a>\u00a0<\/span>and press \u201cLCD laminate start\u201d.
\n\"DetachTake the screen out and there are still bubbles on the screen. Put the screen back into the Bubble Removing Machine for ten minutes and the bubbles are gone.
\n\"TakePut the screen back into the UV Lamp for two minutes. Then we connect the screen to test. The function of the display and touch is good.
\n\"PutLastly, we install the screen on the watch. Attach the adhesive strip to the frame and peel off the protective film.
\n\"Lastly,Connect the screen and turn on the watch. The watch is turned on and all functions work well.
\n\"ConnectFeel free to visit our online shop for Apple Watch parts<\/a> and repair tools.Watch the video below to get a detailed Apple Watch Series 3 Glass Replacement guide.<\/p>\n