{"id":13117,"date":"2022-06-01T20:48:00","date_gmt":"2022-06-01T12:48:00","guid":{"rendered":"https:\/\/rewa.tech\/xiaomi-10-cannot-boot-after-screen-replacement\/"},"modified":"2024-05-10T14:46:19","modified_gmt":"2024-05-10T06:46:19","slug":"xiaomi-10-cannot-boot-after-screen-replacement","status":"publish","type":"post","link":"https:\/\/rewa.tech\/es\/xiaomi-10-cannot-boot-after-screen-replacement\/","title":{"rendered":"Xiaomi 10 no puede arrancar despu\u00e9s de reemplazar la pantalla"},"content":{"rendered":"

Xiaomi 10 no puede arrancar despu\u00e9s de reemplazar la pantalla<\/p>\n

<\/strong><\/p>\n

Modelo:<\/strong> Xiaomi Mi10<\/p>\n

Anunciado:<\/strong> 2020, 13 de febrero<\/p>\n

\"\"<\/p>\n<\/p>\n

Fen\u00f3meno del defecto<\/h2>\n

First, it was only the screen cracked, and the client tried to replace a new screen by himself, but during the replacement, damaged a flex cable. Bought a new flex cable and replace it, then find the phone cannot be booted.<\/p>\n

\"\"<\/p>\n<\/p>\n

Send the phone to a repair shop, and the repair technician judge it’s the CPU with a problem. After resoldering the CPU, assembling the phone, and testing, the issue still remains the same.<\/p>\n<\/p>\n

Soluci\u00f3n de problemas<\/h2>\n

\"\"<\/p>\n

Check the motherboard, it’s obvious that the CPU has been resoldered before.<\/p>\n

Normally, the repair technician will not take the second repair cellphone or board. As we don’t know which part and how it was repaired before, the repair difficulty level is very high! However, there are very important data inside, and the client begs us to repair it for him. So finally, we decide to have a try. <\/p>\n<\/p>\n

The client damaged flex cable is the connection cable between the display little board and the motherboard.<\/p>\n

\"\"<\/p>\n

The display chip is independently integrated into this little board<\/p>\n

\"\"<\/p>\n

Get the flex cable and the boards connected, then power with the DC power supply machine to have a test<\/p>\n

\"\"<\/p>\n

The boot current jumps to around 260mA then drops down<\/p>\n

\"\"<\/p>\n<\/p>\n

Based on the repair experience, this kind of abnormal current is caused by the CPU or the UFS. Besides, the Xiaomi 10 is equipped with Snapdragon 865, which is very easy to hot to cause the CPU poor soldering. So the previous repair technician’s repair logic (resolder the CPU) is OK.<\/p>\n<\/p>\n

Xiaomi 10 should get the battery connected first, then the phone can boot normally. So let’s connect the motherboard with the battery and connect the charging cable to boot. As we can see, there’s no charging current at all.<\/p>\n

\"\"<\/p>\n

Let’s try to boot again with the charging cable connected but the battery connector detached.<\/p>\n

\"\"<\/p>\n

There is a 0.2A charging current<\/p>\n

\"\"<\/p>\n<\/p>\n

By the above phenomenon, we can make a preliminary judgment, it’s the battery current detecting pins with a problem. Let’s take out the motherboard and measure the diode values on the battery connector J5400<\/p>\n

\"\"<\/p>\n<\/p>\n

Refer to the bitmap (or you can measure the diode value on a good motherboard for reference ) to measure the battery data pins<\/p>\n

\"\"<\/p>\n<\/p>\n

The pin 3 (BATT_B+_J2) diode value should be around 589, but the measured result is OL. There must be something wrong with this rail, might be an inside rail broken.<\/p>\n

\"\"<\/p>\n<\/p>\n

On the bitmap, we can see that battery pin 3 is connected with the test point<\/p>\n

\"\"<\/p>\n<\/p>\n

And the measured diode value on the test point is 555, which is normal.<\/p>\n

\"\"<\/p>\n

Jump a wire from Pin 3 of the battery connector to the test point<\/p>\n

\"\"<\/p>\n

Then measure the diode value on pin 3 of J5400 again, and the diode value back to normal.<\/p>\n

\"\"<\/p>\n<\/p>\n

Then let’s put the motherboard into the phone cover to have a test<\/p>\n