{"id":2188,"date":"2020-07-03T00:00:00","date_gmt":"2020-07-03T00:00:00","guid":{"rendered":"http:\/\/192.168.2.19:8666\/?p=1"},"modified":"2023-10-20T15:31:41","modified_gmt":"2023-10-20T07:31:41","slug":"troubleshooting-iphone-x-stuck-on-apple-logo","status":"publish","type":"post","link":"https:\/\/rewa.tech\/es\/troubleshooting-iphone-x-stuck-on-apple-logo\/","title":{"rendered":"Un raro caso de iPhone X atascado en el logo de Apple\uff08iTunes Error 4013\uff09"},"content":{"rendered":"

iPhone gets stuck on the Apple logo, which usually means that there is a problem with the operating system or hardware of the phone.<\/p>\n

Today, we will show you\u00a0a rare case of iPhone X stuck on apple logo,\u00a0and teach you how to diagnose and fix the problem step by step.<\/p>\n

\"Un<\/p>\n

Inspecci\u00f3n cosm\u00e9tica<\/strong><\/p>\n

\"we
\n\"Then<\/p>\n

As we always do, we should run a cosmetic inspection of the motherboard first.<\/p>\n

Check out the condition of the motherboard, whether it is\u00a0deformed or water damaged.<\/p>\n

Then\u00a0get the motherboard installed,\u00a0the phone enters into recovery mode\u00a0automatically.<\/p>\n

Judging by this, the motherboard comes with restore failure. Therefore, the phone cannot enter into the system normally.<\/p>\n

Diagn\u00f3stico\u00a0\u00a0<\/strong><\/p>\n

Let\u2019s restore the phone with 3U Tools and check whether it comes with error 4013.<\/p>\n

The phone can be normally activated after restore.<\/p>\n

Next, check baseband info in the settings.\u00a0If it shows normal,\u00a0we can confirm now that the motherboard is normal.\u00a0The fault is probably related to other parts.<\/p>\n

\"estore<\/p>\n

Get the earpiece speaker and sensor flex cable\u00a0and front camera flex cable installed.<\/p>\n

Turn on the phone,\u00a0the phone is stuck on the Apple logo and keeps restarting.<\/p>\n

Judging by this, the\u00a0fault is related to\u00a0the\u00a0earpiece speaker and sensor flex cable\u00a0or the front camera flex cable.<\/p>\n

\n

\"Check<\/p>\n

Check the earpiece speaker and sensor flex cable carefully, we find that\u00a0the Flood illuminator module\u00a0is moldy.<\/p>\n

Remove the Flood illuminator module,\u00a0we can see that its bonding pad is severely corroded.<\/p>\n

That’s what’s causing the problem.<\/p>\n

Maintenance<\/strong><\/p>\n

\"The
\n\"The<\/p>\n

The next section will explain the detailed repair steps:<\/p>\n

Apply some paste flux to the bonding pad.<\/p>\n

Clean the bonding pad with Soldering Iron.<\/p>\n

Apply solder paste to the severely corroded pad.<\/p>\n

Limpiar despu\u00e9s con PCB Cleaner.<\/p>\n

Apply some paste flux to the bonding pad.<\/p>\n

Get the Flood illuminator module\u00a0in the right position.<\/p>\n

Solder it with Hot Air Gun.<\/p>\n

Prueba<\/strong><\/p>\n

\"Get<\/p>\n

\n

Get the earpiece speaker and sensor flex cable\u00a0installed, then\u00a0assemble the phone.<\/p>\n

The phone turns on normally.\u00a0Since the two flex cables were not connected during the previous restore,\u00a0we need to restore again with the two connected.<\/p>\n

Restore the phone with the help of 3U Tools.<\/p>\n

Once completed,\u00a0the phone enters the system normally, and\u00a0Face ID works normally.<\/p>\n

El proceso de reparaci\u00f3n requiere no s\u00f3lo conocimientos te\u00f3ricos profesionales, sino tambi\u00e9n una gran habilidad manual.<\/p>\n

Start your learning journey with ACADEMIA REWA<\/a> \u00a1Ya!<\/p>\n

\"Start<\/p>\n

Preview this course\uff1aCurso manual de reparaci\u00f3n de placas l\u00f3gicas de iPhone<\/em><\/strong><\/a><\/p>\n

For more details on the operation, watch the video below:<\/p>\n