{"id":2413,"date":"2022-04-26T14:07:41","date_gmt":"2022-04-26T14:07:41","guid":{"rendered":"http:\/\/192.168.2.19:8666\/?p=1"},"modified":"2023-09-20T12:25:00","modified_gmt":"2023-09-20T04:25:00","slug":"iphone-xs-max-face-id-non-funziona","status":"publish","type":"post","link":"https:\/\/rewa.tech\/it\/iphone-xs-max-face-id-not-working\/","title":{"rendered":"Risoluzione dei problemi del Face ID di iPhone XS Max che non funziona - Riparazione del proiettore Dot"},"content":{"rendered":"

Face ID Not Working ‘Move iPhone a Little Lower\/Higher<\/strong>‘ is usually caused by damage to the dot projector and the problem is confirmed to be almost unrepairable. However, there is finally a solution to fix the problem. Today REWA LAB will show you the latest dot projector repair technique!<\/p>\n\n\n\n

\"Face<\/figure>\n\n\n\n

Problema<\/strong><\/h2>\n\n\n\n

When trying to set up Face ID on the iPhone, we get the message ‘move iPhone a little lower\/higher’. Next, switch to the front camera, we found that the name of the lighting effect \u2018Natural Light\u2019 stays the same when the camera detects a person’s face. What’s more, the pop-up notification keeps saying \u2018Move farther away\u2019. Normally, when Portrait mode is ready, the name of the lighting effect \u2018Natural Light\u2019 should turn yellow. Judging by this, the dot projector or relevant circuits of the dot projector might have malfunctioned.<\/p>\n\n\n\n

\"When<\/figure>\n\n\n\n

Diagnosi<\/strong> <\/h2>\n\n\n\n

Take apart the phone and remove the display assembly first. We can see that the dot projector has been water damaged and the crystal on the dot projector is broken. Take out the front camera assembly carefully. Here we recommend using a repair programmer to check the dot projector flex cable. Connecting the dot projector flex cable with the programmer, the results show \u2018Fusing\u2019 which means the dot projector flex cable has been damaged. We need to burn data of the original dot projector flex cable onto a new one and then replace the broken crystal.<\/p>\n\n\n\n

\"Connecting<\/figure>\n\n\n\n
\"Connecting<\/figure>\n\n\n\n
\"Connecting<\/figure>\n\n\n\n
\"Connecting<\/figure>\n\n\n\n

Risoluzione dei problemi<\/strong>   <\/h2>\n\n\n\n

In the first step, we should separate the crystal from the cable. Compared to traditional operations with a hot air gun, we prefer to use an intelligent preheating platform<\/a>. Put the dot projector into the matching rubber mold and separate the crystal from the flex cable carefully with the blade.  Next, we use the repair programmer again to burn the origin data onto the new dot projector flex cable. After completing these two steps, we need to solder the dot projector module and glue a known-good crystal. For detailed instructions, click on the video at the bottom of the article<\/p>\n\n\n\n

\"\"<\/figure>\n\n\n\n

Riassemblaggio e test<\/strong> <\/h2>\n\n\n\n

Apply double-sided adhesive tape on the backside of the front camera, and adhere the dot projector flex cable to the right position. Get the front camera assembly installed and get the logic board assembled and buckle the display assembly. Face ID can be set up successfully, and the phone can be unlocked with Face ID this time.  Tips: The double-sided adhesive tape used here is for the test. We need to glue the dot projector module onto the flex cable after fault clearance.<\/p>\n\n\n\n

Strumenti utilizzati<\/h2>\n\n\n\n