Inicio / Samsung / Samsung A53 no se enciende Reparación

Samsung A53 no se enciende Reparación

Comparte:

The Samsung A53 model is widely recognized as one of the most desirable smartphones currently available. However, like all electronic devices, it is susceptible to occasional operational issues that may prove difficult and frustrating for users. One of the most common problems experienced by users pertains to the device’s failure to turn on, leading to numerous inquiries directed at REWA Tech via email.

While there could be several reasons why a Samsung A53 may not turn on, REWA Tech is committed to providing comprehensive solutions to such problems. Our technical team has developed a step-by-step guide to aid users in troubleshooting and resolving this issue.

Initial Troubleshooting Steps

Check the Battery

Ensure that your phone’s battery is charged. If your phone shows no signs of charging when connected to a charger, try using a different cable and charger to rule out a faulty charging setup.

Soft Reset

Sometimes, a soft reset can resolve the issue. Press and hold the power button along with the volume down button for about 10 seconds. This can sometimes force the phone to restart if the issue is software-related.

Advanced Troubleshooting:

Primary Testing

To begin, test the device by pressing the power button. If the device does not turn on, plug in the charging cable to charge the phone. If the phone remains unresponsive, the device will need to be disassembled for further testing.

Next, we need to get the phone disassembled for further test

Place the phone back down on the heating pad at 100℃ for about 2 minutes, then get a gap with an opening card. Add some alcohol to facilitate separation.

02 Heat the phone on the heating pad at 100 degreen around 2 minutes
03 Disassemble the rear cover with alcohol and opening card

Detach the back cover, and remove the screws that secure the motherboard shielding cover.

04 remove the screws that secure the motherboard

Disconnect the flex cables, take the motherboard out and remove the cameras with the ESD spudger. 

Check the motherboard

Power the motherboard with a direct current supply and trigger the boot process with tweezers, the boot current is 0.

06 Power the cable and boot up with tweezers

Then continue to measure with a multimeter, connect the black probe to the ground and use the red probe for measurement, the voltage is 0. 

07 Boot voltage is 0

Next, protect the motherboard with high-temperature tape, and remove the shielding cover with a hot air gun at 380℃. Measure the diode values of the components around the power IC, the diode values are OK.

08 Remove the shielding conver and measure the diode values around the PMIC
09 All the diode values are OK

It can be judged that the power IC is faulty. Then let’s try to replace the power IC.

Power IC replacement process

Protect the components and chips around the power IC with high-temperature tape, and apply a little bit of solder paste flux. Then heat the IC with a hot air gun at 380℃ and airflow 3. 

10 Remove the power IC

After removing the IC apply some paste flux to the bonding pads, use a soldering iron at 380℃ and mecha de soldadura to remove the tin. Clean the bonding pads with PCB cleaner when the tin is removed.

11 remove the tin with solder wick

The next step, let’s reball the bonding pads of the power IC. Apply the tin paste on the bonding pads with stencil evenly then heat with a hot air gun to form the solder balls at 320℃. 

12 Resolder the PMIC

Apply solder paste on the PCB and align the IC at the proper place, then solder the IC with a hot air gun at 320℃ and airflow 3.

13 Solder it with hot air gun

Clean the motherboard with PCB cleaner and cool it down, then measure with a multimeter, the voltage return to normal, trigger the boot-up with tweezers, and the boot current is also normal. 

14 The boot current is also normal
14 The voltage value is normal

Then we put back the shielding cover and the cameras and install the motherboard. Press the power button and the phone turns on normally.

SAMSUNG A53 Won't Turn On

Assemble the phone and test the functions again

Apply bezel glue and assemble the phone screen with a clamp fixture. Then test all the functions again, and the phone works normally. The issue gets resolved by power IC replacement.

16 Apply the bezel glue

 

Visite Canal REWA en Youtube to watch the detailed operation process

Preguntas frecuentes

How to Fix a Samsung Phone that won’t Turn on?

An issue with the motherboard chip level causes the issue, which requires excellent repair skills and knowledge, as well as professional tools and equipment. It is recommended that you send it back to the official repair center for repair. If your device is out of warranty already and you don’t want to spend a lot on repairing it, ask a local repair shop for assistance.

How can I Become a Cell Phone Technician?

In order to become a cell phone repair technician, you’ll have to learn the device structure, and how to use repair tools, and the key skill is excellent handwork, replacing parts without damaging the motherboard.

A cell phone repair course at Academia REWA is the best way to acquire cell phone repair expertise and skills. We have everything you need to be a cell phone repair technician who can earn a decent living. 

There are three types of training we offer on-site, off-site, and live training. A professional team of trainers and technicians with more than ten years of experience will help you to become a service expert in no time.

Conclusión:

Repairing a smartphone requires a methodical approach to identifying and solving the underlying issue. Whether it’s a simple fix like charging your phone with a different charger or a complex repair like replacing the power IC, understanding the problem is the first step toward resolution.

Comparte:

Academia REWA

Como educador entusiasta y experto en tecnología móvil, REWA Academy ha dedicado su carrera a capacitar a las personas a través de la educación técnica. Con un gran enfoque en la reparación de teléfonos móviles, han desarrollado cursos completos en línea y fuera de línea en la Academia REWA. Su experiencia abarca una amplia gama de áreas, incluyendo la formación de reparación de iPhone, hardware del teléfono, software y técnicas avanzadas de solución de problemas. A través de sus escritos, pretenden desmitificar las complejidades de la tecnología móvil, haciéndola accesible y comprensible tanto para los principiantes como para los profesionales del sector.
formación en reparación de teléfonos

Curso avanzado de reparación de teléfonos

¿Aspira a convertirse en un profesional del sector de la reparación de teléfonos? Si es así, visite la Academia REWA para aprender en profundidad la reparación de teléfonos de la mano de expertos del sector.

Deja una respuesta

Tu dirección de correo electrónico no será publicada. Los campos obligatorios están marcados con *