HUAWEI P30 No Boot Issue Repair

Share:

In this article, we will share some HUAWEI P30 no boot issue repair cases for your reference.

Case 1.

Defect phenomenon

phone cannot startup

Troubleshooting

Firstly, change another set of phone parts to test, still cannot startup. The issue could be confirmed is from the motherboard.

Then take out the motherboard and check the cosmetics, everything looks fine. After that, connect the motherboard and trigger to check the current value of the boot process, it dropped when reach 200mA. Based on the boot sequence check the below voltage values

  Voltage Name
  Normal Value
  Measured Value
  VOUT37_1V2
  1.2V
  0V

0V means there should be some shortage on this voltage relative rails.

As we can see from the schematic, the VOUT37_1V2 is sent out from the U1000 to U300

U1000 out put VOUT37_1V2

U300

U1000 and U300

Apply a 1.3V voltage on the VOUT37_1V2 rail, then check the motherboard under the thermal camera, find the U300 is extremely hot. Remove the U300 and check the VOUT37_1V2 again, there is no short.

Replace a new U300 chip then assemble to test, all the functions are OK.

Case 2.

Defect phenomenon

Press the power button cannot startup

Troubleshooting

Firstly, change another set of phone parts to test, the phone cannot be booted, so the issue comes from the motherboard. 

Then take out the motherboard and check the cosmetics under the microscope, there are no burning components, no mold, no deformation… 

Then check the current with the DC power supply, try to trigger the boot process, and check the current.  It keeps jumping between 0-200mA. Measure the below 3 sets of voltage values

  •  TP3004(USB_DM_CON)
  •  T601.3(USB_DM)
  •  T601.4(SOC_USB_DM)

Normally, should be around 0.61V. But the measured result is 0.23V only. Check the schematic, the 3 voltages are come from U300

U300 SOC USB DM

USB DM

So still there is a high chance, no boot issue is caused by the U300 damage.

Replace it with a new one then test, the phone can be booted normally.

From the above 2 cases we can see, many start-up issues and functional failures might be caused by the U300.

U300 Location P30

Case 3.

Defect phenomenon

Cannot startup

Troubleshooting

The motherboard is clean, check carefully under the microscope, no mold, corrosive, parts missing or deformation, etc.

Connect with the DC power supply machine and try to trigger the boot process, the current keeps jumping between 8-10mA, which is a very low value and quite abnormal.

Based on the repair experience, check the U1000 signal rails first.

After measuring, find the VBAT_SYS shorted to the ground. Then apply power on the VBAT_SYS rail and inspect under the thermal camera, find the C1113 get very hot and (looks extremely bright under the thermal imager )

C1113

So remove C1113 first, then we find the short is gone.

After that, replace a new C1113 with the same specification. Test, all the functions are OK.

Special Coupon Code for you read to the end:   ILoveRepair (Can be used for all courses)

Go to Android Phone Repair Course to learn more.

Share:

REWA Academy

As an enthusiastic educator and expert in mobile technology, REWA Academy has dedicated its career to empowering individuals through technical education. With a keen focus on cellphone repairs, they have developed comprehensive online and offline courses at REWA Academy. Their expertise spans a wide array of areas, including iPhone repair training, phone hardware, software, and advanced troubleshooting techniques. Through their writings, they aim to demystify mobile technology complexities, making it accessible and understandable for both novices and professionals in the field.

Advanced Phone Repair Course

Do you aspire to become a professional in the phone repair industry? If so, visit REWA Academy to learn in-depth phone repair from industry experts.

Leave a Reply

Your email address will not be published. Required fields are marked *

RELATED Articles

How to Fix the iPhone 12 Pro Max Touch Not Working

How to Fix the iPhone 12 Pro Max Touch Not Working

When your phone’s screen becomes unresponsive, the usual solution is to replace it. However, screens are quite expensive these days. In this article, we will introduce an alternative method of...

Samsung A53 Won’t Turn On Repair

The Samsung A53 model is widely recognized as one of the most desirable smartphones currently available. However, like all electronic devices, it is susceptible to occasional operational issues that may prove...

Use the Vivo T1 In the Rain and Won’t Turn On

The client uses the Vivo T1 in the rain and won’t turn on after that. Let’s see the detailed troubleshooting and fixing process. Model: Vivo T1 Announced: 2021, October 20 Defect...