MacBook Pro A1278 Cannot Boot Issue Repair

Share:

Received a Macbook Pro A1278 cannot boot, connect the power cable with MacBook the green light can be turned on normally, but when pressing powder button no response. The client said the issue is caused by water damage and he has disassembled the Macbook and cleaned the motherboard by himself. 

MacBook Pro A1278

Disassemble the Macbook and check the motherboard, it’s has been cleaned thoroughly and looks nice. Check under the microscope again the motherboard also looks OK, didn’t find obvious corrosive components.

Then we check whether there is short on motherboard by multimeter, normaly we start from the inductors.

And after measuring, it’s found the L7260 get shorted, the rest inductors are OK. Refer to the schematic, we can see the L7260 is relative with the PP5V_S3_REG power generation, check the cosmetic around this components also cannot find the corrosive components and chips.

L7260 

So we can only use the DC power supply to apply voltage and find out the shorted components.

Tips, even through the voltage is PP5V_S3_REG, but we cannot apply 5V voltage directly, as the instantaneous large current might cause serious damage to the motherboard!

DC Power Supply 5A 30V

(5A 30V DC Power Supply – Suitable for Laptop Repair)

It’s advised to apply voltage from 0Volt to 5volts gradually. And when we apply voltage to 2V (current around 2A) a capacitor get burned with smoke. 

C6601

Check the schematic, C6601 is a filter type capacitor only. So we can just remove it directly.

A1278 Cannot Boot

Assemble the MacBook to test again, the issue remains still cannot be booted.

Then continue to check the public voltage, it’s normal. But when we measure the voltage PP3V3_S5_REG on L7220, there is no voltage.

Based on the boot sequence

First, when EC is ready to work, it will receive the SMC_BC_ACOK signal(adapter detect signal), then read the adapter information. As the green light is on, it means the adapter can be detected normally.

Then, EC will send out voltage enable signal PP3V3S5_EN_L to start the PP3V3_S5_REG voltage output. Measure the voltage on the PP3V3S5_EN_L signal, it’s in low-level status which is normal. So PP3V3_S5_REG cannot be generated might be caused by relative chip damage.

Check the cosmetic of components related to PP3V3_S5_REG, with no corrosive or obvious damage.

Then replace Q7220 with a new one directly. But the issue still did not get resolved.

PP3V3S5_EN_L

Then based on repair experience, go to check the standby chip U7200

  • the Pin 16 with normal power supply
  • the Pin 8/17 no linear voltage
  • the Pin 13 linear voltage enable signal no voltage

Pin 13 linear enable signal P5V3V3_REG_EN will be generated through R2723. Measure both sides of R2723, there is no voltage. Power off to measure the diode values are OK.

R7273

Track the signal P5V3V3_REG_EN is from pin 3 of U7941. Check the U7941, chip appearance looks fine. Measure the voltage on U7941

  • Pin 2 with high voltage level which is OK
  • Pin 1 voltage supply is also OK

So the chip U7941 might be damaged. Get it replaced with a new one, then the MacBook can be booted normally.

U7941

Summary: The issue finnaly gets fixed by removing the shorted filter type capacitor C6601 and replacing chip U7941. 

Share:

REWA Academy

As an enthusiastic educator and expert in mobile technology, REWA Academy has dedicated its career to empowering individuals through technical education. With a keen focus on cellphone repairs, they have developed comprehensive online and offline courses at REWA Academy. Their expertise spans a wide array of areas, including iPhone repair training, phone hardware, software, and advanced troubleshooting techniques. Through their writings, they aim to demystify mobile technology complexities, making it accessible and understandable for both novices and professionals in the field.

Advanced Phone Repair Course

Do you aspire to become a professional in the phone repair industry? If so, visit REWA Academy to learn in-depth phone repair from industry experts.

Leave a Reply

Your email address will not be published. Required fields are marked *

RELATED Articles

How to Fix the iPhone 12 Pro Max Touch Not Working

How to Fix the iPhone 12 Pro Max Touch Not Working

When your phone’s screen becomes unresponsive, the usual solution is to replace it. However, screens are quite expensive these days. In this article, we will introduce an alternative method of...

Samsung A53 Won’t Turn On Repair

The Samsung A53 model is widely recognized as one of the most desirable smartphones currently available. However, like all electronic devices, it is susceptible to occasional operational issues that may prove...

Use the Vivo T1 In the Rain and Won’t Turn On

The client uses the Vivo T1 in the rain and won’t turn on after that. Let’s see the detailed troubleshooting and fixing process. Model: Vivo T1 Announced: 2021, October 20 Defect...