A Rare Case Of iPhone X Stuck On Apple Logo(iTunes Error 4013)

iPhone gets stuck on the Apple logo, which usually means that there is a problem with the operating system or hardware of the phone.

Today, we will show you a rare case of iPhone X stuck on apple logo, and teach you how to diagnose and fix the problem step by step.

A Rare Case Of iPhone X Stuck On Apple Logo(iTunes Error 4013)

Cosmetic Inspection

we should run a cosmetic inspection of the motherboard first. Check out the condition of the motherboard, whether it is deformed or water damaged.
Then get the motherboard installed, the phone enters into recovery mode automatically. Judging by this, the motherboard comes with restore failure. Therefore, the phone cannot enter into the system normally.

As we always do, we should run a cosmetic inspection of the motherboard first.

Check out the condition of the motherboard, whether it is deformed or water damaged.

Then get the motherboard installed, the phone enters into recovery mode automatically.

Judging by this, the motherboard comes with restore failure. Therefore, the phone cannot enter into the system normally.

Diagnosis  

Let’s restore the phone with 3U Tools and check whether it comes with error 4013.

The phone can be normally activated after restore.

Next, check baseband info in the settings. If it shows normal, we can confirm now that the motherboard is normal. The fault is probably related to other parts.

estore the phone with 3U Tools and check whether it comes with error 4013.

Get the earpiece speaker and sensor flex cable and front camera flex cable installed.

Turn on the phone, the phone is stuck on the Apple logo and keeps restarting.

Judging by this, the fault is related to the earpiece speaker and sensor flex cable or the front camera flex cable.

Check the earpiece speaker and sensor flex cable carefully, we find that the Flood illuminator module is moldy. Remove the Flood illuminator module, we can see that its bonding pad is severely corroded. That's what's causing the problem.

Check the earpiece speaker and sensor flex cable carefully, we find that the Flood illuminator module is moldy.

Remove the Flood illuminator module, we can see that its bonding pad is severely corroded.

That’s what’s causing the problem.

Maintenance

The next section will explain the detailed repair steps:   Apply some paste flux to the bonding pad.   Clean the bonding pad with Soldering Iron.   Apply solder paste to the severely corroded pad.   Clean with PCB Cleaner afterward.   Apply some paste flux to the bonding pad.   Get the Flood illuminator module in the right position.   Solder it with Hot Air Gun.
The next section will explain the detailed repair steps:   Apply some paste flux to the bonding pad.   Clean the bonding pad with Soldering Iron.   Apply solder paste to the severely corroded pad.   Clean with PCB Cleaner afterward.   Apply some paste flux to the bonding pad.   Get the Flood illuminator module in the right position.   Solder it with Hot Air Gun.

The next section will explain the detailed repair steps:

Apply some paste flux to the bonding pad.

Clean the bonding pad with Soldering Iron.

Apply solder paste to the severely corroded pad.

Clean with PCB Cleaner afterward.

Apply some paste flux to the bonding pad.

Get the Flood illuminator module in the right position.

Solder it with Hot Air Gun.

Test

Get the earpiece speaker and sensor flex cable installed, then assemble the phone. The phone turns on normally.

Get the earpiece speaker and sensor flex cable installed, then assemble the phone.

The phone turns on normally. Since the two flex cables were not connected during the previous restore, we need to restore again with the two connected.

Restore the phone with the help of 3U Tools.

Once completed, the phone enters the system normally, and Face ID works normally.

The repair process requires not only professional theoretical knowledge but also proficient handwork skills.

Start your learning journey with REWA ACADEMY now!

Start your learning journey with REWA ACADEMY now!

Preview this course:iPhone Logic Board Repair Handwork Course

For more details on the operation, watch the video below:

Share Love:

Picture of REWA Team

REWA Team

We are the REWA Team, a division of REWA Technology consisting of repair technicians, experts, and marketers. Each article we produce is crafted with great care and input from various individuals.

Subscribe On YouTube

Did you enjoy the article? Our team of industry experts provides valuable insights and practical solutions to all your repair needs. Subscribe to our channel today and get access to all our latest videos, updates, and valuable content.
Subscribe

Recommended For You

Leave a Reply

Your email address will not be published. Required fields are marked *